|
|
|
|
Yanshancounty Fengliyuan Pipe Fittings Equipment Manufacture Co.,Ltd
Sektör : [ Hidrolik ve Pres ]
Chengdong Developing Zone,East to Yanshantown,Cangzhou City,Hebei Province,China
Cangzhou - - Çin
 | Empon Shing Empon | | | |
 | +86-317-6193236 | |
 |
E-Mail
|
 | +86-317-6193226 | |
 |
http://www.flygjsb.com/English/
|
|
Hidrolik ve Pres
Üretici
2000
10-50
1-2 Million US$
|
|
Son Güncelleme: 13.01.2024
Bu firmanın bilgilerini güncellemek ve değiştirmek istiyorsanız.Giriş
Bu bilgiler firmalar tarafından verilen bilgiler olup TurkeyBusiness.Com bu bilgilerin doğruluğu garanti etmez.
Ayrıca bu bilgilerden dolayı sorumlu tutulamaz.
|
|
Hidrolik ve Pres sektöründeki firmaları görmek için ..
Hidrolik ve Pres sektör ürünleri görmek için
|
|
| steel pipe bending hydraulic machine |
|
STEEL PIPE BENDING HYDRAULIC MACHINE
Kategori : Boru Sanayi
|
The Main Technical Parameters of The Pipe Bending Machine
1、 Master cylinder： OD.140mm, ID.: 100mm , diameter of the rod: φ70mm
effective strock:2 m the max thrust of the 2 cylinders 60T. normal pressure is 21mpa.
2、 Hydraulic pump station
a、station configuration: 10scy plunger pump 1 set 、 5.5KW Motor 1 set ( to converse frequency
adjust the speed of the master pump)
CB-40 gear pump 1 set 、5.5KW Motor 1 set ( fast forward and backward).
The working speed ; 0-25cm/min , the max backward speed:400cm/min,(380V or 220V,50HZ)
b. hydraulic motor 4 piece.
c. hydraulic controlling valves 1 unit.
3、The guiding part of the main machine is controlled by four wheels, the clamp holding different size run
By the hydraulic motor, it open and closed by hand.
4、Medium—frequency power supply：160 KW, 500-1000HZ.
The total power of the machinery part: 11KW,380V or 220V,50HZ or 60 HZ
5、Assembly parts
a、clamp wheels （four for the round pipe）、fixture made of 45# cast steel
b、master fuselage、weldment、the main pushing board are welded board
c、screw、chain、standard parts and bearing are national standards
d、the guider is dovetail groove slide plate mode
The works and the scope of supply of the supplier
1. Design and manufacture the pipe bending machine
2. Guide to install the equipment as the equipment arrives at the factory of buyer
3. Debugging and test run the equipment
4. Main machine part, hydraulic pump station.
5. fixture (front clamps device):
for round pipe: 1 piece for OD 5 inch pipe.
6. The bending radius adjusting part and the turning part.
7. The heating device:
M-frequency ark: 1 set 200KW
The capacitor 1 set
The electric reactor 1 set
Water cooling cable 2.5mX2 pieces
Quenching transformer 500KVA 1 set.
Induction heating coil: 1 piece for OD 5 inch pipe.
9. The equipment foundation drawing, hydraulic principle drawing, electrical diagram, machinical drawing, manual operating instruction 1 copy for each.
| steel pipe bending hydraulic machine hakkında yapılan yorumlar |
Bu ürünle ilgili yorum yapılmamış
steel pipe bending hydraulic machine ile ilgili yorum yazınız
|
|
|
|